Physical Description
Connect the plug directly to the TL-WR710N to finish
hardware connection.
Package Contents
The provided power plug may differ from the picture due
to different regional power specifications. Here we use the
EU version as an example.
TL-WR710N LED:
Note:
Status
Indication
The device is working properly.
System is booting.
Solid Green
Blinking
The Ethernet Cable or USB Device is
connecting to the product.
Quick Installation Guide
WiFi Pocket Router/AP/TV Adapter/Repeater
USB Reset
LAN/WAN
LAN
TL-WR710N
Ethernet Cable
After hardware connection, please write down the
Wireless Password and SSID on the label of your
Router for later use. Both are case-sensitive.
USB：It is used to connect USB Flash or Hard Disk for ꢀle sharing and
Mobile devices for charging.
Reset：It is used to reset the Router to its factory defaults.
Model:TL-WR710N
S/N:XXXXXXXXXXXX
Ver:2.0
LAN/WAN: Must use this port to connect to your Modem while in
Router mode. For all other modes, use it as an additional LAN port.
MAC:B0487A663D6C
WiFi Pocket Router/AP/TV Adapter/Repeater
Wireless Password/PIN:12345678
SSID:TP-LINK_663D6C
LAN: Connect your ethernet enabled devices for wired network
access. In client mode, use it to give wireless access to a wired-only
device. In access point mode, use it to receive network access from
your local network.
WiFi Pocket Router/AP/TV Adapter/Repeater
Model:TL-WR710N
Ver:2.0
S/N:XXXXXXXXXXXX
Default Access:
Username: admin
Password
:
admin
MAC:B0487A663D6C
MODEL NO. TL-WR710N
Wireless Password/PIN:12345678
SSID:TP-LINK_663D6C
FCC ID: TE7WR710N
IC: 8853A-WR710N
Resource CD
QIG
Wireless Password/PIN: Default Password
For more detailed information about Reset, please refer to
*
*
Appendix: Troubleshooting
.
SSID: Default Wireless Network Name
MODEL NO. TL-WR710N
Hardware Connection
1
Wireless Router Mode (Default)
2
Access Point Mode
3
4
Client Mode
5
WISP Client Router Mode
Repeater Mode
Create an instant private wireless network
and share Internet to multiple Wi-Fi
devices.This mode is suitable for hotel rooms
and home networks.
Create a wireless network from an Ethernet
connection. This mode is suitable for dorm
rooms or homes where there's already a wired
router but you need a wireless hotspot.
In this mode, this device can be connected to
another device via Ethernet cable and act as
an adapter to grant your wired devices
access to a wireless network, especially for a
Smart TV, Media Player, or Game console
only with an Ethernet port.
Use as
access from
Provider (WISP), and share that access with
local devices.
a
client router to receive Internet
Wireless Internet Service
Repeat signal from an existing wireless
network. This mode is suitable to extend
wireless coverage, reaching devices that
were previously too far from your primary
a
router to maintain
connection.
a
stable wireless
(Note: if the hotel’s Internet has an
authentication process, you will need to
authenticate only once and only on one
device.)
(Note: if the hotel’s Internet has an authentica-
tion process, you will need to authenticate it
on EACH device.)
The repeated signal will display the same
network name and password as your existing
wireless network.
Wired Ethernet
Connection
Wired Ethernet
Connection
SSID: def
Protected by
NAT Firewall
Cable
Cable
Instant Wireless Connection
(The examples illustrated below are from Windows 7. If you are using a diꢁerent Windows, or a Mac Operating System, your screenshots may look diꢁerent, but the procedure is the same.)
Go to Start
network status and tasks
adapter settings. Right click Wireless
Network Connection, and select
>
Control Panel
>
View
Set up the TCP/IP Protocol in "Obtain an IP
address automatically" and "Obtain DNS
sever address automatically" mode on your
PC. Click OK.
Click the Wireless Network icon
desktop. Select the Default SSID of the
TL-WR710N, then click Connect.
on your
Enter the Default Password. Click OK or
Next.
The ꢀgure below indicates you have
successfully connected to your network.
1
2
3
4
4
>
Change
Properties. Double click Internet Protocol
Version 4 (TCP/IPv4) in the item list.
Operation Mode Conꢀguration
Open
a
Web browser and go to the page
After a successful login, click “Quick Setup” from the menu
to conꢀgure your TL-WR710N. Click “Next”.
Choose the Working Mode you need, then click “Next” and
refer to the corresponding mode on the back page for
further instruction.
1
2
3
and Password: admin, both in lower case letters.
Click OK.
|