OPERATOR'S
MAN UAL
and MAINTENANCE INSTRUCTIONS for
TECUMSEH
HM80 HM90
HM100 HHM80
MODEL
HORIZONTAL CRANKSHAFT
AIR COOLED • FOUR-CYCLE ENGINE
THIS SYMBOL POINTS OUT IMPORTANT SAFETY INSTRUCTIONS WHICH IF NOT FOLLOWED COULD ENDANGER THE PER-
SONAL SAFETY AND/OR PROPERTY OF YOURSELF AND OTHERS. READ AND FOLLOW ALL INSTRUCTIONS IN THIS MANUAL
AND ANY PROVIDED WITH THE EQUIPMENT ON WHICH THIS ENGINE IS USED BEFORE ATTEMPTING TO OPERATE YOUR
TECUMSEH ENGINE.
THESE SYMBOLS MAY APPEAR ON THE ENGINE:
California Proposition 65
WARNING:
The engine exhaust from this product contains chemicals
known to the State of California to cause cancer, birth defects or other reproductive harm.
3-1-99 181-630-14
COOLING
FINS
ENGINES WHICH ARE CERTIFIED TO COMPLY WITH CALIFORNIA
AND U.S. EPA EMISSION REGULATIONS FOR ULGE ENGINES, are
certified to operate on regular unleaded gasoline, include the following
emission control system(s): EM, TWC (if so equipped); Do not include any
user adjustable features - therefore no other adjustments are needed.
STOP
SWITCH
OIL FILL PLUG
& DIPSTICK (IF
SO EQUIPPED)
OIL FILL PLUG
AND DIP-
STICK
SPARK PLUG
WIRE
OIL & FUEL RECOMMENDATIONS
MODEL AND
D.O.M. DECAL
TO OPERATE ENGINE, YOU WILL NEED THE FOLLOWING:
À
A CLEAN, HIGH QUALITY DETERGENT OIL.
Be sure original container is marked:
SPARK PLUG
MUFFLER
FUEL FILL
CAP
A.P.I. service "SF"-"SJ".
FOR SUMMER (ABOVE 320F; 00C) USE SAE 30 OIL.
Tecumseh specially formulated oil is available at any Authorized
Tecumseh Service Outlet. Order as part number 730225. Using LEVERS &
multigrade oil will increase oil consumption.
LINKAGE
FOR WINTER (BELOW 320F; 00C) USE SAE 5W30 OIL.
Tecumseh specially formulated oil is available at any Authorized
Tecumseh Service Outlet. Order as part number 730226.
CARBURE-
TOR
(SAE 10W is an acceptable substitute.)
(BELOW 00F ONLY): SAE 0W30 OIL is an acceptable substitute.
DO NOT USE SAE 10W40 OIL.
OIL SUMP CAPACITY:
Models HM70-80-100, HMXL70: 26 ounces
(1-5/8 U.S. pints)
FUEL TANK
AIR INTAKE
Model HHM80: 34 ounces
(2-1/8 U.S. pints)
Á
A FRESH, CLEAN, UNLEADED REGULAR, UNLEADED PREMIUM,
OR REFORMULATED AUTOMOTIVE GASOLINE ONLY. DO NOT
USE LEADED GASOLINE.
RECOIL
STARTER
AIR CLEANER
NOTE: DO NOTUSE GASOLINE CONTAINING METHANOL(WOOD
ALCOHOL). Gasoline containing up to 10% ethanol or grain alcohol
(“Gasohol”) may be used but requires special care when engine is
unused for ex tended periods. See “STORAGE” instructions on Page
5.
OIL DRAIN
PLUG
STARTER
HANDLE
NOTE: Use clean oil and fuel and store in approved, clean, covered
containers. Use clean fill funnels.
Never use “stale” gasoline left over from last season or stored for long
Figure 1
Page 1
181-630-14
periods.
MAINTENANCE (Continued)
STARTING
(Continued)
 COOLING SYSTEM (see Figure 1 and Figure 5):
Á ELECTRIC STARTER:
IMPORTANT: Frequently remove grass clippings, dirt and debris
from cooling fins, air intake screen and levers and linkage. This
will help ensure adequate cooling and correct engine speed.
A. Move choke lever (see Figure 3 or 4) to “FULL CHOKE POSITION”.
NOTE: IF RESTARTING A WARM ENGINE AFTER A SHORT
SHUTDOWN, MOVE CHOKE LEVER TO “NO CHOKE
POSITION”.
B. Move equipment control (see manufacturer’s instructions) or engine
control to “START”.
C. Push starter button or turn ignition switch key (see equipment
manufacturer’s instructions) to crank engine.
D. Crank engine until it fires. When it starts, release starter button or
ignition switch key and move choke lever to “1/2 CHOKE” until engine
runs smoothly and then to “NO CHOKE POSITION”.
COOLING
FINS
If engine falters, move choke lever to “1/2 CHOKE” until engine runs
smoothly and then to “NO CHOKE POSITION”.
AIR INTAKE SCREEN
(IF SO EQUIPPED)
NOTE: If engine fires, but does not continue to run, move choke lever
to “NO CHOKE POSITION’’ and crank engine until it starts.
NOTE: If engine again fires, but does not continue to run, move
choke lever to “FULL CHOKE” and repeat instructions B, C
and D until engine starts.
Figure 5
à SPARK PLUG (see Figure 6):
This spark ignition system meets all requirements of the Canadian
Interference-Causing Equipment Regulations. This engine complies with
allcurrentAustralian and NewZealand limitations regarding electromagnetic
interference. Check spark plug yearly or every 100 operating hours.
STOPPING
À
Á
Move equipment control or any ignition stop switch on engine to “STOP” or
“OFF” (see equipment manufacturer’s instructions).
A. Clean area around spark plug.
B. Remove and inspect spark plug.
Push stop switch (if so equipped see Figure 1) located next to spark plug
C. Replace spark plug if electrodes are pitted, burned or porcelain is
cracked. For replacement use Champion RJ-17LM only.
on engine against spark plug and hold it in this position until engine is
completely stopped.
NOTE: A resistor spark plug must be used for replacement.
D. Check electrode gap with wire feeler gauge and set gap at .030 if
necessary.
 AFTER ENGINE IS STOPPED:
E. Install spark plug, tighten securely.
ELECTRODES
A. Close fuel valve (if so equipped).
. DISCONNECT SPARK PLUG WIRE FROM SPARK PLUG AND
KEEP IT AWAY FROM SPARK PLUG.
C. TURN IGNITION SWITCH KEY (IF SO EQUIPPED) TO “OFF”
POSITIONANDREMOVE KEYFROMSWITCH, THIS WILLREDUCE
THE POSSIBILITY OF UNAUTHORIZED STARTING OF ENGINE
WHILE EQUIPMENT IS NOT IN USE.
NEVER STORE ENGINE WITH FUEL IN TANK INDOORS OR IN
ENCLOSED, POORLYVENTILATEDAREAS, WHERE FUELFUMES
MAY REACH AN OPEN FLAME, SPARK OR PILOT LIGHT AS ON
A FURNACE, WATER HEATER, CLOTHES DRYER OR OTHER
GAS APPLIANCE.
.030 GAP
PORCELAIN
Figure 6
Ä AIR CLEANER:
MAINTENANCE
IMPORTANT: NEVER RUN ENGINE WITHOUT COMPLETE
AIR CLEANER INSTALLED ON ENGINE.
A. TO SERVICE FILTER(S) (see Figure 7):
1. FOAM FILTER:
WARNING: TEMPERATURE OF MUFFLER AND NEARBY AREAS
MAY EXCEED 1500F (650C). AVOID THESE AREAS.
À OIL LEVEL:
Clean and re-oil every three (3) months or every 25 operating
hours. Clean and re-oil daily if used in extremely dusty conditions.
Check oil level every five (5) operating hours and before each use. See
“FILL OIL SUMP OR CHECK OIL LEVEL’’ on Page 2.
NOTE: DO NOT OIL FOAM FILTER ON AIR CLEANER "A".
a. Wash in water and detergent solution and squeeze (don’t
twist) until all dirt is removed.
b. Rinse thoroughly in clear water.
c. Wrap in a clean cloth and squeeze (don’t twist) until completely
dry.
Á CHANGE OIL (see Figure 1):
Change oil after first two (2) operating hours and every 25 operating hours
thereafter, more often if operated in extremely dusty or dirty conditions.
Change oil while engine is still warm from recent running.
d. Saturate with engine oil and squeeze (don’t twist) to distribute
oil and remove excess oil.
. DISCONNECT SPARK PLUG WIRE FROM SPARK PLUG AND
KEEP IT AWAY FROM SPARK PLUG.
2. PAPER FILTER:
B. Clean area around oil drain plug (see Figure 1).
C. Position equipment so engine oil drain plug is lowest point on engine.
D. Remove oil drain plug and oil fill plug to drain oil.
E. Install oil drain plug and tighten securely.
DO NOT ATTEMPT TO CLEAN OR OIL FILTER.
Replace once a year or every 100 operating hours, more often if
used in extremely dusty conditions. Replacement filters are
available at any Authorized Tecumseh Service Outlet.
F. Fill oil s ump with re comme nde d oil. S e e “OIL & FUEL
RECOMMENDATIONS’’ on Pages 1 and 2 and “FILL OIL SUMP OR
CHECK OIL LEVEL” on Page 2.
G. Install oil fill plug and tighten securely.
H. Wipe up any spilled oil.
MAINTENANCE (Continued)
MAINTENANCE (Continued)
B. TO REMOVE AND INSTALL FILTER(S):
AIR CLEANER "A" (see Figure 7):
Å ALTERNATOR AND BATTERY (if so equipped):
A. ALTERNATOR:
1. Remove wing nut and cover.
2. Slide foam filter (if so equipped) off paper filter.
3. Discard paper filter.
For electrical problems such as inoperative starter or discharged
batterysee equipmentmanufacturer’s instructions forfuse replacement,
maintenance and repairs.
4. Clean inside of base and cover thoroughly.
5. Install new paper filter on base.
6. Slide foam filter (if so equipped) over paper filter.
7. Install cover and wing nut. Tighten wing nut securely.
AIR CLEANER "B" & "C" (see Figure 7):
1. Remove wing nut and cover.
B. BATTERY:
1. When servicing battery, always connect cables to battery exactly as
they were before removal (ground cable to battery negative [- or
neg.] post). If incorrectly connected, fuse (if so equipped), will blow
and alternator won’t charge battery. If this happens, connect cables
correctly and replace fuse.
2. Never expose engine ignition system to battery power. If battery
cable or any live wire contacts ignition system ground wire, engine
ignition system may be damaged.
2. Slide foam filter off paper filter.
3. Inspect filters for discoloration or dirt accumulation. If either is
present, service per preceding “TO SERVICE FILTER(S)”
instructions.
4. Remove paper filter (if service is necessary).
5. Clean topside of base and inside of cover thoroughly.
6. Install paper filter .
3. If external battery charger is used, disconnect positive (+ or pos.)
cable from battery to prevent possible damage.
4. See battery manufacturer’s instructions for service and storage.
Æ
CHECKENGINE ANDEQUIPMENTOFTENFOR LOOSE NUTS,
BOLTS AND ATTACHMENTS AND KEEP THESE ITEMS
TIGHTENED.
7. Slide foam filter over paper filter.
8. Install cover and wing nut. Tighten wing nut securely.
NOTE: In Air Cleaner “C” application, make sure to position scoop
correctly:
ADJ USTMENTS
•
•
WINTER (Below 320F; 00C): Scoop should be pointed directly
at muffler.
DO NOT MAKE UNNECESSARY ADJUSTMENTS. FACTORY SETTINGS
ARE SATISFACTORY FOR MOST CONDITIONS. IF ADJUSTMENTS ARE
NEEDED, PROCEED AS FOLLOWS:
SUMMER (Above 320F; 00C): Scoop should be pointed towards
blower housing (approximately 450 clockwise from “winter posi-
tion”).
À REMOTE CONTROL (see Figure 8 or 9):
For satisfactory engine performance, engine and equipment control must
be adjusted properly. To check engine control adjustments, proceed as
follows:
IMPORTANT: In order for engine to operate smoothly and effi-
ciently, it is important for scoop to be in proper position for sea-
son.
Set equipment control at “FAST” or “HIGH SPEED” and keep it in this
position. In this position, engine control lever should touch “HIGH SPEED
STOP”. If it does, the controls are adjusted correctly and no further
adjustment should be necessary.
COVER
WING NUT
NOTE: If engine control lever does not touch “HIGH SPEED STOP”,
proceed to CONTROL A in Figure 8 or CONTROL B in Figure 9.
CONTROL A (see Figure 8):
A. Loosen clamp screw so remote control cable can be moved in cable
clamp (do not remove cable clamp from control bracket or disconnect
remote control cable from engine control lever).
BASE
AIR CLEANER "A"
PAPER FILTER
FOAM FILTER (IF SO EQUIPPED)
B. Move engine control lever so it is touching “HIGH SPEED STOP” and
hold it in this position.
WING NUT
C. Tighten clamp screw securely so cable clamp will hold remote control
cable in place when equipment control is used.
WING NUT
COVER
COVER
The engine controls should now be adjusted correctly.
If additional adjustments are needed, make them at the equipment control
(see equipment manufacturer’s instructions).
FOAM FILTER
FOAM FILTER
CONTROL B (see Figure 9):
PAPER
FILTER
PAPER FILTER
BASE
A. Hold control lever in an upward position, as close as possible to “HIGH
SPEED STOP’’ and loosen, but do not remove remote cable stop
screw.
BASE
B. Move remote cable stop upward on remote control cable so it holds
control lever against “HIGH SPEED STOP” and tighten remote cable
stop screw securely.
AIR CLEANER "C"
Figure 7
AIR CLEANER "B"
The engine controls should now be adjusted correctly.
If additional adjustments are needed, make them at the equipment control
(see equipment manufacturer’s instructions).
181-630-14
ADJ USTMENTS (Continued)
STORAGE
NEVER STORE ENGINE WITH FUEL IN TANK INDOORS OR IN
ENCLOSED, POORLY VENTILATED AREAS, WHERE FUEL FUMES
MAY REACH AN OPEN FLAME, SPARK OR PILOT LIGHT AS ON A
FURNACE, WATER HEATER, CLOTHES DRYER OR OTHER GAS
APPLIANCE.
REMOTE CONTROL CABLE
CABLE CLAMP
CLAMP SCREW
CONTROL
BRACKET
HIGH SPEED
IF ENGINE IS TO BE UNUSED FOR 30 DAYS OR MORE, PREPARE AS
FOLLOWS:
MANUAL
CONTROL
(IF SO EQUIPPED)
À DRAIN FUEL SYSTEM:
CONTROL LEVER
A. Remove all gasoline from carburetor and fuel tank to prevent gum
deposits from forming on these parts and causing possible malfunction
of engine.
DRAIN FUEL INTO APPROVED CONTAINER OUTDOORS, AWAY
FROMOPENFLAME. BE SURE ENGINE IS COOL. DO NOTSMOKE.
IDLE
B. Run engine until fuel tank is empty and engine stops due to lack of fuel.
NOTE: If “Gasohol” has been used, complete above instructions and
then put 1/2 pint of “Unleaded” gasoline into fuel tank and
repeat above instructions.
NOTE: Tecumseh SMART STARTTM gasoline preservative and
stabilizer is an acceptable alternative in minimizing the
formation of fuel gum deposits during storage. Add stabilizer
to gasoline in fuel tank or storage container. Always follow mix
ratio found on stabilizer container. Run engine at least 10
minutes after adding stabilizer to allow it to reach carburetor.
HIGH SPEED STOP
STOP
CONTROL A
Figure 8
Á DRAIN CARBURETOR (if so equipped):
CONTROL BRACKET
Drain carburetor by pressing upward on bowl drain (see Figure 10), which
is located below carburetor (see Figure 1).
REMOTE CONTROL
CABLE
DRAIN FUEL INTO APPROVED CONTAINER OUTDOORS, AWAY
FROM OPEN FLAME. BE SURE ENGINE IS COOL. DO NOT SMOKE.
CLAMP SCREW
NOTE: Do not drain carburetor if using fuel stabilizer.
CABLE CLAMP
CONTROL LEVER
CARBURETOR
BOWL DRAIN
HIGH SPEED
STOP
REMOTE
CABLE STOP
SCREW AND
STOP
Figure 10
CONTROL B
 CHANGE OIL:
Figure 9
Change oil if it has not been changed in the last three (3) months. See
“CHANGE OIL” instructions in “MAINTENANCE” section.
Á CARBURETOR:
Ifyou thinkyourcarburetorneeds adjusting, see yournearestAUTHORIZED
TECUMSEH SERVICE OUTLET. Engine performance should not be
affected at altitudes up to 7,000 feet. For operation at higher elevations,
contact your AUTHORIZED TECUMSEH SERVICE OUTLET.
à OIL CYLINDER BORE:
A. Remove spark plug. Squirt one (1) oz. (30 ml) of clean engine oil into spark
plug hole.
B. Cover spark plug hole with a rag.
C. Crank engine over, slowly, several times.
 ENGINE SPEED:
AVOIDSPRAYFROMSPARKPLUG HOLE WHENCRANKING ENGINE
OVER SLOWLY.
NEVER TAMPER WITH ENGINE GOVERNOR WHICH IS FACTORY
SETFOR PROPER ENGINE SPEED. OVERSPEEDING ENGINE ABOVE
FACTORYHIGHSPEEDSETTING CANBE DANGEROUS. CHANGING
OF ENGINE GOVERNED SPEED WILL VOID ENGINE WARRANTY.
Install spark plug. Do not connect spark plug wire.
Ä DC.LEAN ENGINE:
Remove any clippings, dirt, or chaff from exterior of engine.
For engine adjustments and/or repairs not covered in this “OPERATOR’S
MANUAL” see “WARRANTY & REPAIR” on Page 6.
Å BATTERY (if so equipped):
See equipment manufacturer’s instructions for proper storage of battery.
Page 5
181-630-14
WARRANTY AND REPAIR
For engine adjustment, repairs, or warranty service not covered in this manual, contact you nearest AUTHORIZED
TECUMSEH SERVICE OUTLET. It is listed in your telephone book yellow pages under "Engines, Gasoline."
If you have a general understanding of internal combustion engine and wish to repair and service your engine
yourself, a "MECHANICS HANDBOOK" which covers repairs and adjustments not covered in this OPERATOR'S
MANUAL is available from your AUTHORIZED TECUMSEH SERVICE OUTLET. Order as Part No. 692509.
Tecumseh manufactures and is responsible only for the engine used on this power equipment. If repair or service
is needed for unit, other than engine, contact service source as recommended by equipment manufacturer.
Warranty requirements for engines sold outside of the USA may vary from country to country. For warranty details
for your specific country, contact your national Tecumseh Service Distributor. If help is needed in locating your
national service distributor, you may contact Tecumseh c/o International Service Coordinator, Engine & Transmis-
sion Group Service Division, 900 North Street, Grafton, Wisconsin USA 53024-1499. Telephone in USA is
414-377-2700.
LIMITED WARRANTY FOR NEW TECUMSEH ENGINES
AND ELECTRONIC IGNITION MODULES
For the time period shown below from the date of purchase, Tecumseh Products Company will, at its option as the exclusive remedy, either repair or replace for
the original purchaser, free of charge, any part of any new Tecumseh engine which is found, upon examination by any Tecumseh Authorized Service Outlet or by
Tecumseh’s factory in Grafton, Wisconsin, to be DEFECTIVE IN MATERIAL AND/OR WORKMANSHIP, except as provided below. This Limited Warranty DOES
NOT COVER (i) any Tecumseh engine or part(s) thereof used to power any vehicle in competitive racing and/or used on any commercial or rental track, or (ii) defects
or damage caused by alterations or modifications of new Tecumseh engines or parts or by normal wear, accidents, improper maintenance, improper use or abuse
of the product, or failure to follow the instructions contained in an Instruction Manual for the operation of the new Tecumseh engine or part. The cost of normal
maintenance or replacement of service items which are not defective shall be paid for by the original purchaser. At the time warranty service is requested, evidence
must be presented of the date of purchase by the original purchaser. Any charge for making service calls and/or for transporting any engine or part(s) thereof to and
from the place where the inspection and/or warranty work is performed is payable solely by the purchaser. The purchaser is responsible for any damage or loss incurred
in connection with the transportation of any engine or part(s) thereof submitted for inspection and/or warranty work. WARRANTY SERVICE CAN ONLY BE
PERFORMED BY
A
TECUMSEH AUTHORIZED SERVICE OUTLET OR BY TECUMSEH AT ITS FACTORY IN GRAFTON, WISCONSIN. Warranty service can
Tecumseh Authorized Service Outlet (any Tecumseh Registered Service Dealer, Tecumseh Master Service Dealer, Tecumseh
be arranged by contacting either
a
Authorized Service Distributor, or Tecumseh Central Warehouse Distributor) or by contacting Tecumseh c/o Service Manager, Engine and Transmission Group Service
Division, 900 North Street, Grafton, Wisconsin 53024-1499.
ENGINE WARRANTY PERIOD
"CONSUMER USE" +
"COMMERCIAL USE" ++
Warranty
Category†
Within U.S.A.
Outside U.S.A.
and Canada
Within
Outside
and Canada
USA and Canada
USA and Canada
(A)
(B)
90 day
90 day
1 Year
No Warranty
1 Year
No Warranty
1 Year
1 Year
(C)
(D)
(E)
(H)
(K)
2 Years
2 Years
2 Years
2 'n 10*
2 'n 10*
1 Year
1 Year
1 Year
1 Year
1 Year
2 'n 10*
1 Year
1 Year
1 Year
1 Year
1 Year
2 Years**
2 Years
2 'n 10*
2 'n 10*
*
2
1
years on engine, 10 years on electronic ignition.
year for Australia/New Zealand for rotary mower engines.
**
+
For purposes of this warranty policy, "consumer use" shall mean consumer's personal, residential, household use by the original retail purchaser.
+ + For purposes of this warranty policy, "commercial use" shall mean all other uses, including use for commercial, income producing, or rental purposes.
†The engine warranty category of your engine can be determined by review of the engine model number on the "Important Engine Information" decal. One letter in
the engine model number will be surrounded by parens (A), (B), (C), (D), (E), (H) or (K) and that letter is your engine warranty category designation. IN CALIFORNIA
ONLY, THIS EXPRESS WARRANTY IS SUPPLEMENTED BY THE TECUMSEH CALIFORNIA EMISSION CONTROL WARRANTY STATEMENT.
THIS EXPRESS WARRANTY IS IN LIEU OF ALL OTHER EXPRESS WARRANTIES. Neither Tecumseh nor any of its affiliates makes any warranties,
representations, or promises, written or oral, as to the quality of the engine or any of its parts, other than as set forth herein. ANY IMPLIED WARRANTY OF
MARKETABILITY OR FITNESS FOR
A
PARTICULAR PURPOSE, TO THE EXTENT THAT EITHER MAY APPLY TO ANY TECUMSEH ENGINE OR PART(S)
THEREOF, SHALL BE LIMITED IN DURATION TO THE PERIODS OF THE EXPRESS WARRANTIES SHOWN IN THE WARRANTY PERIOD CHART ABOVE
AND TO THE EXTENT PERMITTED BY LAW ANY AND ALL IMPLIED WARRANTIES ARE EXCLUDED. IN NO EVENT WILL TECUMSEH BE LIABLE FOR ANY
INCIDENTAL, CONSEQUENTIAL OR SPECIAL DAMAGES AND/OR EXPENSES. Some states do not allow limitations on how long an implied warranty lasts or
the exclusion or limitation of incidental or consequential damages, so the above limitation(s) or exclusion(s) may not apply to you. This Limited Warranty gives you specific
legal rights and you may also have other legal rights which vary from state-to-state.
6-1-95
EXAMPLE: HM80
ENGINE
MODEL
155000P
SPEC.
NUMBER
(B)
5001A
SERIAL
NUMBER
FILL IN:
WARRANTY
PERIOD
ENGINE
MODEL
SPEC.
NUMBER
WARRANTY
PERIOD
SERIAL
NUMBER
TECUMSEH PRODUCTS COMPANY
Engine & Transmission Service Group Service Division • 900 North Street • Grafton, WI, USA • 53024-1499
Page 6
181-630-14
CALIFORNIA & US EPA EMISSION CONTROL WARRANTY STATEMENT
The U. S. Environmental Protection Agency (“EPA”), the California Air Resources Board (“CARB”) and Tecumseh Products
Co. are pleased to explain the Federal and California Emission Control Systems Warranty on your new utility or lawn and
garden equipment engine. In California, new 1995 and later utility and lawn and garden equipment engines must be de-
signed, built and equipped to meet the State’s stringent anti-smog standards. In other states, new 1997 and later model year
engines must be designed, built and equipped, at the time of sale, to meet the U.S. EPA regulations for small non-road
engines. Tecumseh Products Co. will warrant the emission control system on your utility or lawn and garden equipment
engine for the periods of time listed below, provided there has been no abuse, neglect, unapproved modification, or improper
maintenance of your utility or lawn and garden equipment engine.
Your emission control system may include parts such as the carburetor, ignition system and exhaust system. Also included
may be the compression release system and other emission-related assemblies.
Where a warrantable condition exists, Tecumseh Products Co. will repair your utility or lawn and garden equipment engine at
no cost to you for diagnosis, parts and labor.
MANUFACTURER’S EMISSION CONTROL SYSTEM WARRANTY COVERAGE
Emission control systems on 1995 and later model year California utility and lawn and garden equipment engines are
warranted for two years as hereinafter noted. In other states, 1997 and later model year engines are also warranted for two
years. If, during such warranty period, any emission-related part on your engine is defective in materials or workmanship, the
part will be repaired or replaced by Tecumseh Products Co.
OWNER’S WARRANTY RESPONSIBILITIES
As the utility or lawn and garden equipment engine owner, you are responsible for the performance of the required mainte-
nance listed in your Owner’s Manual, but Tecumseh Products Co. will not deny warranty solely due to the lack of receipts or
for your failure to provide written evidence of the performance of all scheduled maintenance.
As the utility or lawn and garden equipment engine owner, you should, however, be aware that Tecumseh Products Co. may
deny you warranty coverage if your utility or lawn and garden equipment or a part thereof has failed due to abuse, neglect,
improper maintenance or unapproved modifications.
You are responsible for presenting your utility or lawn and garden equipment engine to a Tecumseh Authorized Service
Outlet (any Tecumseh Registered Service Dealer, Tecumseh Authorized Service Distributor or Tecumseh Central Ware-
house Distributor) as soon as a problem exists. The warranty repairs should be completed in a reasonable amount of time,
not to exceed 30 days.
Warranty service can be arranged by contacting either a Tecumseh Authorized Service Outlet or by contacting Tecumseh
Products Co., c/o Service Manager, Engine and Transmission Group Service Division, 900 North Street, Grafton, WI 53024-
1499. Telephone 1-414-377-2700, or see your local telephone yellow pages under “Engines, Gasoline” for the name,
address and telephone number of a Tecumseh Authorized Service Outlet near you.
IMPORTANT NOTE
This warranty statement explains your rights and obligations under the Emission Control System Warranty (“ECS Warranty”)
which is provided to you by Tecumseh Products Co. pursuant to California law. Tecumseh Products Co. also provides to
original purchasers of new Tecumseh Products Co. engines. The Tecumseh Products Co. Limited Warranties for New
Tecumseh Engine and Electronic Ignition Modules (“Tecumseh Products Co. Warranty”) which is enclosed with all new
Tecumseh Products Co. engines on a separate sheet. The ECS Warranty applies only to the emission control system of
your new engine. To the extent that there is any conflict in terms between the ECS Warranty and the Tecumseh Products
Co. Warranty, the ECS Warranty shall apply except in any circumstances in which the Tecumseh Products Co. Warranty
may provide a longer warranty period. Both the ECS Warranty and the Tecumseh Products Co. Warranty describe important
rights and obligations with respect to your new engine.
Warranty service can only be performed by a Tecumseh Products Co. Authorized Service Outlet, or by Tecumseh Products
Co. at its factory in Grafton, WI. At the time of requesting warranty service, evidence must be presented of the date of sale
to the original purchaser. The purchaser shall pay any charges for making service calls and/or for transporting the products
to and from the place where the inspection and/or warranty work is performed. The purchaser shall be responsible for any
damage or loss incurred in connection with the transportation of any engine or any part(s) thereof submitted for inspection
and/or warranty work.
If you have any questions regarding your warranty rights and responsibilities, you should contact Tecumseh Products Co. at
1-414-377-2700.
181-630-14
Page 7
EMISSION CONTROL SYSTEM WARRANTY
Emission Control System Warranty (“ECS Warranty”) for 1995 and later model year California utility and lawn and garden equipment
engines (for other states, 1997 and later model year engines):
A.APPLICABILITY: This warranty shall apply to 1995 and later model year California utility and lawn and garden equipment engines
(for other states, 1997 and later model year engines). The ECS Warranty Period shall begin on the date the new engine or
equipment is delivered to its original, end-use purchaser, and shall continue for 24 consecutive months thereafter.
B.GENERAL EMISSIONS WARRANTY COVERAGE: Tecumseh Products Co. warrants to the original, end-use purchaser of the
new engine or equipment and to each subsequent purchaser that each of its utility and lawn and garden equipment engines is:
1.Designed, built and equipped so as to conform with all applicable regulations adopted by the Air Resources Board pursuant to its
authority in Chapters 1 and 2, Part 5, Division 26 of the Health and Safety Code, and
2.Free from defects in materials and workmanship which, at any time during the ECS Warranty Period, will cause a warranted
emissions-related part to fail to be identical in all material respects to the part as described in the engine manufacturer’s applica-
tion for certification.
C. The ECS Warranty only pertains to emissions-related parts on your engine, as follows:
1.Any warranted, emissions-related parts which are not scheduled for replacement as required maintenance in the Owner’s Manual
shall be warranted for the ECS Warranty Period. If any such part fails during the ECS Warranty Period, it shall be repaired or
replaced by Tecumseh Products Co. according to Subsection 4 below. Any such part repaired or replaced under the ECS
Warranty shall be warranted for any remainder of the ECS Warranty Period.
2.Any warranted, emissions-related part which is scheduled only for regular inspection as specified in the Owner’s Manual shall be
warranted for the ECS Warranty Period. A statement in such written instructions to the effect of “repair or replace as necessary”,
shall not reduce the ECS Warranty Period. Any such part repaired or replaced under the ECS Warranty shall be warranted for
the remainder of the ECS Warranty Period.
3.Any warranted, emissions-related part which is scheduled for replacement as required maintenance in the Owner’s Manual, shall
be warranted for the period of time prior to the first scheduled replacement point for that part. If the part fails prior to the first
scheduled replacement, the part shall be repaired or replaced by Tecumseh Products Co. according to Subsection 4 below. Any
such emissions-related part repaired or replaced under the ECS Warranty, shall be warranted for the remainder of the ECS
Warranty Period prior to the first scheduled replacement point for such emissions-related part.
4.Repair or replacement of any warranted, emissions-related part under this ECS Warranty shall be performed at no charge to the
owner at a Tecumseh Authorized Service Outlet.
5.The owner shall not be charged for diagnostic labor which leads to the determination that a part covered by the ECS Warranty is
in fact defective, provided that such diagnostic work is performed at a Tecumseh Authorized Service Outlet.
6.Tecumseh Products Co. shall be liable for damages to other original engine components or approved modifications proximately
caused by a failure under warranty of an emission-related part covered by the ECS Warranty.
7.Throughout the ECS Warranty Period, Tecumseh Products Co. shall maintain a supply of warranted emission-related parts
sufficient to meet the expected demand for such emission-related parts.
8.Any Tecumseh Products Co. authorized and approved emission-related replacement part may be used in the performance of any
ECS Warranty maintenance or repair and will be provided without charge to the owner. Such use shall not reduce Tecumseh
Products Co. ECS Warranty obligations.
9.Unapproved add-on or modified parts may not be used to modify or repair a Tecumseh Products Co. engine. Such use voids
this ECS Warranty and shall be sufficient grounds for disallowing an ECS Warranty claim. Tecumseh Products Co. shall not be
liable hereunder for failures of any warranted parts of a Tecumseh Products Co. engine caused by the use of such an unap-
proved add-on or modified part.
EMISSION-RELATED PARTS INCLUDE THE FOLLOWING:
1. Carburetor Assembly and its Internal Components
a) Fuel filter
4. Catalytic Muffler (if so equipped)
a) Muffler gasket (if so equipped)
b) Exhaust manifold (if so equipped)
b) Carburetor gaskets
c) Intake pipe
5. Crankcase Breather Assembly and its Components
a) Breather connection tube
2. Air Cleaner Assembly
a) Air filter element
3. Ignition System, including:
a) Spark plug
b) Ignition module
c) Flywheel assembly
7.22.97 EPA/CARB
181-630-14
Page 8
|